Robot fleet supervisor

Robot Fleet Supervisor: Hardware That Watches the Run

Published

a robot's logs tell you what the robot believes happened. when a deployment slips, that is one account among several, and it comes from the machine under suspicion. a supervisor is the second witness : hardware that moves with the fleet and records what was going on around the run.

what a robot fleet supervisor is :

A robot fleet supervisor is an independent system that observes robots at work, records the conditions around each run, and keeps that record next to the robots' own data, so a result can be checked against something other than the robot's own report.

it does not dispatch tasks and it does not drive the robots. that is the job of robot fleet management software. the supervisor's job is evidence.

why robots cannot supervise themselves :

  • a robot only logs what its own sensors saw. when a camera topic drops to 0 Hz, the log goes quiet exactly where the answer was.
  • the conditions that change a result are often outside the robot : the lighting on the night shift, a layout that moved, a pallet left in the aisle.
  • clocks drift, drivers restart, feedback drops out. a run reported as complete is not always a run that succeeded.
  • on a mixed fleet, every vendor logs differently. an outside record is the one thing the whole fleet has in common.

when a deployment slips, engineering, the integrator and the site each have a theory, and nobody holds a record all three accept. the documented cases are in why robot deployments fail.

the OORB Mobile Station :

our supervisor hardware is the Mobile Station : a mobile unit on four wheels that drives with your robots. its mast rises to see over the work, it records the conditions of every run, and it syncs them with RunFP wherever the fleet goes.

what the Mobile Station carries :

  • 360° camera : Ricoh Theta, on the mast head
  • depth camera : RealSense D435, on the mast head
  • 2D lidar : RPLIDAR C1, a 360° plane for position
  • ambient light sensor : how lit the floor is, every run
  • IMU : the station's own motion and tilt
  • edge computer : Jetson Orin Nano, data stays on-prem

five sensors and one edge computer. the cameras give the outside view of the task, the lidar gives the station its position in the room, and the ambient light sensor and IMU record how lit the floor is and how the station itself is moving.

supervising hardware, not only software :

a learned policy is one of several things that can change between two runs. so can a gripper, a motor, a firmware version or a sensor mount. on a fleet, wear is uneven : two robots with the same software stop behaving the same.

RunFP keeps the robot and sensor configuration with every run, next to the code, the model and the dependencies. when results drop, the change is ranked across all of them : code, model, dependencies, hardware, environment or setup. what is captured is described in robot run provenance.

where the data goes :

the Mobile Station processes its data on board, on its own edge computer. RunFP installs on your own machines. recordings, results and reports stay on your network, and every result keeps the code, model, hardware and conditions behind it, so your team and your customer can check the same record.

what supervision is used for :

you can start without the hardware :

RunFP works on its own from the data your robots already record : ROS bags, MCAP files and test-rig exports, with no changes to your robot. the Mobile Station is for the sites where the answer depends on what was happening around the robot. Get RunFP free and open your first run, or read get started with RunFP.

frequently asked questions :

What is a robot fleet supervisor ?

A robot fleet supervisor is an independent system that observes robots at work, records the conditions around each run, and keeps that record next to the robots' own data. It gives a team a second account of what happened, separate from what the robot reported about itself.

What does the OORB Mobile Station carry ?

Five sensors and one edge computer: a 360° camera and a depth camera on the mast head, a 2D lidar, an ambient light sensor, an IMU, and a Jetson Orin Nano that processes the data on board.

Where does the supervisor's data go ?

It is processed on the Mobile Station's own edge computer and syncs with RunFP, which runs on your own machines. Recordings, results and reports stay on your network.

Do I need supervisor hardware to use RunFP ?

No. RunFP works on its own from the data your robots already record: ROS bags, MCAP files and test-rig exports. The Mobile Station adds an outside view of the conditions around a run.

How is a fleet supervisor different from fleet management software ?

Fleet management software directs the robots: it assigns tasks and coordinates traffic. A supervisor measures them: it records what happened around each run so that reliability can be measured and failures explained.

the robot tells you what it did. the supervisor tells you what happened.

if you run a fleet and want an outside record of its conditions, tell us about the site and we will show you what the Mobile Station would see.

Robot failing in the field? Get help now